1GSa/s 2CH 7in LCD Digital Storage Oscilloscope 100MHz Bandwidth DSO2C10 HANTEK. Bus decoding and protocol analysis: RS232/UART, I2C, SPI, CAN, LIN.
Abundant SCPI remote control commands/ 2. 5 bits digital voltage meter and 6 bits hardware frequency indicator function. 32 kinds of auto measurements with statistics, realtime statistics of maxmum, minimum, standrad deviation and etc. 2 channels, each channel has independent knob control, and adjustment is more convenient.Suitable for troops, college laboratory, scientific research unit and factory production line. Item Type: Digital Storage Oscilloscope Material: ABS Color: As shown in the picture. Display high frequency and random glitches. Average waveform times: 4, 8, 16, 32, 64, 128.
DC, AC or ground (DC, AC, GND). 2ns/div-100s/div, 1, 2, 5 step. ±0.5divX Minimal base gear. Edge trigger, pulse width trigger Video trigger, slope trigger, timeout trigger Window trigger, pattern trigger, interval trigger, runt trigger, UART trigger, LIN trigger, CAN trigger, IIC trigger.Voltage difference between cursorsV Time difference between cursorsT The reciprocal of T, in Hz (1/T). Double peak value, frequency, average value, maximum value, minimum value, period, top value, middle value, bottom value, amplitude, root mean square, rising edge overshoot, falling edge preshoot, period root mean square, period average , Rise time, fall time, positive pulse width, negative pulse width, positive duty cycle, negative duty cycle, FRR, FFF, falling edge overshoot, rising edge preshoot, pulse width, FRF, FFR, LRR, LRF, LFR, LFF.
DC RMS, AC RMS, DC. =+, -, ×, ÷, FFT.
Rectangular, Hanning, Heming, Blackman, Bartlett, flat top. Single display or full display. 9 types of files can be saved and recalled internally, including settings, waveforms, and reference. CSV file, BMP picture (24 digits).
7in TFT LCD screen diagonally. 800 (horizontal) x 480 (vertical) pixels. 1s, 5s, 10s, 30s, unlimited.00-120VACRMS(±10%), 45Hz to 440Hz, CAT 120-240VACRMS(±10%), 45Hz to 66Hz, CAT. +104(+40): 90% relative humidity 106122 (+4150): 60% relative humidity. Instructions: 1: Plug in the power and turn on 2: Set the switch on the probe to X10 and connect the probe to channel 1 of the oscilloscope. To do this, align the slot on the probe connector with the protrusion on the CH1 BNC, press it down to connect, then turn to the right to lock the probe in place, and connect the probe tip and reference lead to the "probe unit "On the connector, the label on the panel is: 5V at lKHz. 3: Press the Auto Set button. The screen shows a square wave with a frequency of 1kHz and a voltage of 5V peak-to-peak. 4: Observe whether it is a square wave, adjust the probe to keep the probe in the best state (the waveform is normal). 1 x BNC Connecting Line.
Instead of leaving negative/neutral feedback or opening a dispute. Our listing price includes the value of goods, packaging cost, and export. Please check with your country's.We will reply your message within 48 hours. If you do not receive our reply within 48 hours, pls.
Post a message again because sometimes our message system may block some emails. If you are satisfied with our service, pls. Our aim is to provide Level Customer Service, your recognition will encourage us greatly and serve you better.We strive to keep all our customers satisfy. We will do our up most to exceed your expectations in customer service, communication and dispatching of your orders.
The item "1GSa/s 2CH 7in LCD Digital Storage Oscilloscope 100MHz Bandwidth DSO2C10 HANTEK" is in sale since Monday, February 22, 2021. This item is in the category "Business, Office & Industrial\Test, Measurement & Inspection\Analysers & Data Acquisition\Oscilloscopes & Vectorscopes". The seller is "rightshere" and is located in Shenzhen. This item can be shipped worldwide.