DSO2C15 Digital Storage Oscilloscope 150MHZ Dual Channel 1GSa/s (EU 100-240V)

  

Digital storage oscilloscope with 5-digit digital voltmeter and 6-digit hardware frequency meter functions. 2CH dual-channel design, 150MHZ bandwidth, 1GSa/s sampling rate. Trigger: edge, pulse, video, slope, timeout, window, pattern, interval, runt, UART, LIN, CAN, SPI, IIC. Bus decoding and protocol analysis: RS232/UART, I2C, SPI, CAN, LIN, storage depth 8Mpts. Rich SCPI remote control commands, easy operation and high measurement accuracy.

Item Type: Oscilloscope Material: ABS. Display high frequency and random glitches.

Average waveform times: 4, 8, 16, 32, 64, 128. DC, AC or ground (DC, AC, GND).

Maximum 4M For Dual Channels. 2ns/div-100s/div, 1, 2, 5 steps. ±0.5divX minimum time base gear. Edge trigger, pulse width trigger Video trigger, slope trigger, timeout trigger Window trigger, pattern trigger, interval trigger, runt trigger, UART trigger LIN trigger, CAN trigger IIC trigger. V Time difference between cursors?

Double value, frequency, average value, maximum value, minimum value, period, top value, middle value, bottom value, amplitude, mean squares root, rising edge overshoot, falling edge preshoot, period root mean, period average, Rise time, fall time, positive pulse width, negative pulse width, positive duty cycle, negative duty cycle, FRR, FFF, falling edge overshoot, rising edge preshoot, pulse width, FRF, FFR, LRR, LRF, LFR, LFF. DC RMS, AC RMS, DC. =, +, -, ×, ÷, FFT.

Rectangular, Hanning, Heming, Blackman, Bartlett, flat top. Single display or full display. 9 types of files can be saved and recalled internally, including settings, waveforms, and references. CSV file, BMP picture (24 bit). 7in TFT LCD screen diagonally. 800 (horizontal) x 480 (vertical). 1s, 5s, 10s, 30s, unlimited. 100-120VACRMS(±10%), 45Hz to 440Hz, CAT? 120-240VACRMS(±10%), 45Hz to 66Hz, CAT? How to Use: 1: Plug in the power and turn on 2: Set the switch on the probe to and connect the probe to channel 1 of the oscilloscope. To do this, align the slot on the probe connector with the protrusion on the CH1 BNC, press it down to connect, then turn to the right to lock the probe in place, and connect the probe tip and reference to the "probe "On the connector, the label on the panel is: -5V at lKHz. 3: Press the Auto Set button.

The screen shows waves with a frequency of 1kHz and a voltage of 5V -to. 4: Observe whether waves, adjust the probe to keep the probe in the best state (the waveform is normal). 1 x BCN Connecting Cable. Instead of leaving negative/neutral feedback or opening a dispute. Our listing price includes the value of goods, packaging cost, and export.

Please check with your country's. We will reply your message within 48 hours. If you do not receive our reply within 48 hours, pls. Post a message again because sometimes our message system may block some emails.

If you are satisfied with our service, pls. Our aim is to provide Level Customer Service, your recognition will encourage us greatly and serve you better.

We strive to keep all our customers satisfy. We will do our up most to exceed your expectations in customer service, communication and dispatching of your orders. This item is in the category "Business & Industrial\Test, Measurement & Inspection\Analyzers & Data Acquisition\Oscilloscopes & Vectorscopes". The seller is "globebestdeal" and is located in this country: CN. This item can be shipped worldwide.