HANTEK DSO2D10 2CH Digital Storage Oscilloscope 100MHz 1GSa/s 8M withSignal Source

HANTEK DSO2D10 2CH Digital Storage Oscilloscope 100MHz 1GSa/s 8M w/Signal Source. Digital storage oscilloscope, builtin 1CH 25MHz signal generator, which makes electronic maintenance and car maintenance more convenient. Abundant SCPI remote control commands.

Trigger: edge, pulse, video, slope, timeout, window, pattern, interval, runt, UART, LIN, CAN, SPI, IIC. It can save settings, waveforms, reference waveforms, CSV, pictures and other data formats. Support threshold test, realize free measurement in the screen. Item Type: Digital Storage Oscilloscope. Number of average waveforms: 4, 8, 16, 32, 64, 128. DC, AC or ground (DC, AC, GND). 2ns/div-100s/div, 1, 2, 5 steps. Window trigger, pattern trigger, interval trigger, runt trigger, UART trigger, LIN trigger, CAN trigger, IIC trigger.

The reciprocal of T, in for Hertz (1/T). Double peak value, frequency, average value, maximum value, minimum value, period, top value, middle value, bottom value, amplitude, root mean square, rising edge overshoot, falling edge preshoot, period root mean square, period Average value, rise time, fall time, positive pulse width, negative pulse width, positive duty cycle, negative duty cycle, FRR, for FFF, falling edge overshoot, rising edge preshoot, pulse width, FRF, FFR, LRR, LRF, LFR, LFF. =+, -, ×, ÷, FFT. Rectangular, for Hanning, for Heming, for Blackman, for Bartlett, flat roof. Sine wave, square wave, ramp wave, Exp, noise, DC.

Sine wave, square wave, triangular wave. 800 (horizontal) x 480 (vertical) pixels. 1s, 5s, 10s, 30s, infinite. 1: Plug in the power and turn on. 2: Set the switch on the probe to X10 and connect the probe to channel 1 of the oscilloscope.

3: Press the Auto Set button. The screen shows a square wave with a frequency of 1kHz and a voltage of 5V peak-to-peak. 4: Observe whether it is a square wave, adjust the probe to keep the probe in the best state (the waveform is normal). Operating Instructions of the Signal Generator. Connect EXT TRIG GEN OUT and connect the other end to the unit that needs to receive signals.

Press WAVE GEN to start the signal generator. Press F1 to select waveform, sine, square wave, DC, etc. Press WAVE GEN, F2 frequency, period selection, F3 amplitude selection. 1 x USB Data Cable. Instead of leaving negative/neutral feedback or opening a dispute. Our listing price includes the value of goods, packaging cost, and export.

Please check with your country's. We will reply your message within 48 hours. If you do not receive our reply within 48 hours, pls. Post a message again because sometimes our message system may block some emails. If you are satisfied with our service, pls.

Our aim is to provide Level Customer Service, your recognition will encourage us greatly and serve you better. We strive to keep all our customers satisfy.

We will do our up most to exceed your expectations in customer service, communication and dispatching of your orders. The item "HANTEK DSO2D10 2CH Digital Storage Oscilloscope 100MHz 1GSa/s 8M withSignal Source" is in sale since Monday, February 22, 2021.

This item is in the category "Business, Office & Industrial\Test, Measurement & Inspection\Analysers & Data Acquisition\Oscilloscopes & Vectorscopes". The seller is "goohbusiness" and is located in Shenzhen.

This item can be shipped worldwide.

Brand: HANTEK
Country/Region of Manufacture: China
Digital Oscilloscope Resolution: 12-bit
Material: ABS
Maximum Bandwidth: 100MHZ
Maximum Real-Time Sampling Rate: 1 GSa/s
Model: DS02D10
MPN: Does Not Apply
Number of Channels: 2
Oscilloscope Type: Digital Storage Oscilloscope (DSO)
Type: Digital Storage Oscilloscope (DSO)
Weight: Approx.